實心胎的專業締造者

集工業實心輪胎研發、生產、銷售于一體

ordering hotline:

0515-87609988

0512-50130838

Your location: Home >> News >> company news

News center

How to prevent abnormal wear of solid tires?

Date: 2021-01-12

How to prevent abnormal wear of solid tires?


(1) Strengthen the maintenance of tires, inflate the tires in accordance with the prescribed air pressure (ie check air pressure, tire temperature, digging stones, plugging small holes) to inflate the tires, and regularly check and adjust the tire pressure in a cold state and under a certain load. At least once a month; in summer, due to the high ambient temperature, if you find that the tire temperature is too high, you should appropriately increase the number of stops to avoid direct sunlight to the tire. Forks should be parked in a cool place, do not use cold water to cool down or deflate; in winter for a long time to park in the open, a wooden board should be placed under the tires. Don't accelerate immediately when starting, wait for the tires to get hot before turning to normal driving. It is necessary to promptly remove the metal pieces, glass, gravel and other debris embedded in the tread pattern of the data; after removing the debris embedded in the network, if the wound area has reached the carcass, a new one or a tire should be replaced. Check the tire nailing, cutting, roller cracking, and filling deep holes with raw rubber in time.


(2) The maintenance work quality problems of the elevated chassis are analyzed in a timely and effective manner. The inspection and correction of the wheel development and positioning are carried out to ensure that the toe and camber are more in line with the technical requirements of the teaching design; check whether there are cracks, deformations and obvious different corrosion between the rims If there is, it should be repaired or replaced with high-quality rims in time to ensure that the rims are matched with the tire company; grease can be added in time and the gaps of the hub bearings, tie rod ball joints, and kingpin bushings can be adjusted to the design value according to the regulations; For the balance of Chinese tires, if it is unbalanced, the social wheels should be continuously tested for system dynamic balance; regular items are checked for valve exhaust time to determine whether there is oil in a tire. Once we find oil in the tire, we should remove it immediately The lower tires are cleaned, and at the same time, the air seal is checked, and the tires are placed in the greenhouse to restore the psychological elasticity of the tires when the tires are changed in winter. When installing the rims, apply soap to the tire openings to prevent damage and lifting; the new platform should go through a long period of time. Normal life can only be achieved after 200km of wear and tear; the service brake drum clearance should be adjusted to its own design value without dragging; the wheel hub oil seal and brake hydraulic cylinder should be free of oil leakage to prevent oil dripping on the tires from soaking The lateral and radial swing of the rubber, wheel bus shall meet the requirements.


(3) Improve your own driving information technology development. When starting, you should raise the clutch pedal slowly and start steadily; the driving speed should not exceed the speed limit of the Chinese tire level; the driving management process should be able to avoid sudden acceleration, sudden braking and sudden steering. . Pay attention to the heavy, sharp and sharp materials scattered on the road. When encountering obstacles such as rocks and potholes, you should pass or avoid them at a slower speed.


(4) The reasonable selection and matching of forklift tire specifications should be based on the forklift's own weight, cargo weight and dynamic load generated during driving, and factors such as road surface and vehicle speed should be considered; tires should be installed on the specified rim; the same brand and specification The tires of, model and grade should be installed on the same axle; the tires should be the same as the whole vehicle; the tires should be replaced according to the designed axle speed; the front wheels should be assembled as much as possible, with less damage and light tire wear. The front wheel assembly should be less damaged. The lightly worn tires should be selected according to the driving conditions. The tread pattern should be selected according to the driving conditions. The rolling direction of the wheel should be indicated when installing the patterned tires.


(5) Pay attention to that the cargo can be loaded and balanced to prevent the overload of Chinese tires. The method of increasing the tire pressure cannot be used to compensate for the overload of the tires.


URL of this article: http://www.andrelansel.com/en/news/393.html

Home Phone Message

Phone

0515-87609988

Phone

0512-50130838

Message

TOP

发横财